BeQuiet! Light Wings (BL072): Sturdy rotor with ARGB LEDs

… and airflow

Illuminated fans from BeQuiet! have the advantage over many competing models in a more robust rotor design. This is also due to the fact that it is not made of “light conductive” material and therefore some may not like the Light Wings fans, but aerodynamically they have the edge over other models. This is not only because of the choice of raw materials and their robustness, but also the overall shape of the blades.

… and airflow

With airflow measurements, we can well explain why the test tunnel is shaped the way it is. It doesn’t consist of two parts just so that the “exhaust” can be conveniently clogged for pressure measurements. The anemometer (i.e. the wind speed measuring instrument) is held together by two parts, two formations, through the flanges.

The front part, at the beginning of which the fan is mounted, becomes steadily narrower and from about two thirds of the way through the cross-section is smaller than that of a 120 mm fan. The reason for this is that the cross-section of the anemometer is always smaller than that of the fans tested. The taper towards the anemometer fan is as smooth as could be chosen and the tunnel walls are smooth. This has minimized the occurrence of unnatural turbulence.

The difference between the cross section at the intake (fan under test) and at the constriction point (anemometer) also means a difference in dynamic pressure, the principles of the Venturi effect apply here. In order to avoid distortion at this level and to ensure that the fan airflow is not different from what it actually is, the Bernoulli equation must be applied to the measured values (for maximum accuracy, the calculation also takes into account the internal cross-sectional area of the anemometer, i.e. its inactive part ). After all this, it is again possible to confront our results with the paper parameters.

We use an Extech AN300 anemometer with a large 100 mm fan for the measurements. Its big advantage over other anemometers is that it is made for bidirectional sensing. This allows tests at different fan orientations. However, the “pull” position is more suitable or accurate for measurements, even though it may not seem so at first glance, but we’ll explain.

Here, we get to the second part of the tunnel, the part behind the anemometer. It is part of the whole device, mainly to allow a laminar flow of air to arrive at the rotor of the anemometer. Otherwise, uncontrolled side whirls would be reflected in the results, which are inconsistent with accurate measurements. Therefore, we will test the flow in the pull position. If anyone would like us to elaborate more on this topic, we can elaborate further at any time in the discussion below the article. Ask away. 🙂

The rear of the tunnel ensures, among other things, that the air supply to the anemometer fan is laminar

In regard to the anemometer, we shall return for a bit to noise measurements and to setting modes according to fixed noise levels. It may have occurred to you as you were reading that the anemometer fan is also a source of sound that needs to be filtered out when measuring fans. For this reason, we insert a securing pad between the frame and the anemometer fan before each measurement and mode setting according to the fixed noise level. This, by the way, also holds the anemometer fan during static pressure measurements.


  •  
  •  
  •  
Flattr this!

BeQuiet! Dark Rock Elite – The new king of coolers?

I will start this year’s cooler tests with a real treat. I’ve prepared a review of the Dark Rock Elite cooler, the absolute top of BeQuiet!’s range. This is a premium cooler offering very high performance at low noise levels thanks to its sophisticated design in combination with high-end fans. I’m very curious to see how it performs compared to the high-end coolers I’ve had the opportunity to test over the past year. Read more “BeQuiet! Dark Rock Elite – The new king of coolers?” »

  •  
  •  
  •  

BeQuiet! Pure Wings 3 (BL108): Efficient and “cheap” in 140 mm

The long break is over, back to fans. BeQuiet! recently updated its entry-level line – Pure Wings – and at least the slower 140-millimeter models have to be on your radar. The Pure Wings 3 fans in the BL108 variant represent an extremely efficient low-cost option for some situations, while not suffering from the common shortcomings of their price class. What’s quiet here is not only the aerodynamic component, but also the motor one. Read more “BeQuiet! Pure Wings 3 (BL108): Efficient and “cheap” in 140 mm” »

  •  
  •  
  •  

12VHPWR cable thermal imaging: Different PSU, different temps

Something for warm-up. We’ll start our ATX 3.0 PSU tests with perhaps the most talked about topic surrounding them, the temperatures of the new cables with 16-pin PCIe connectors. The overview of the PSUs of twelve brands answers well the question of how the manufacturers handled which models. With high current loads, the temperature differences can be quite significant, both on the connector housings and on the wire insulation. Read more “12VHPWR cable thermal imaging: Different PSU, different temps” »

  •  
  •  
  •  

Leave a Reply

Your email address will not be published. Required fields are marked *