When something is “worth it” and it’s bigger than enough for some, making a smaller version is definitely a good idea. Something similar happened with the Arx 700 Air, from which the scaled-down Arx 500 Air was derived. It has taken all the good qualities and also the wider range of features of the original case. This includes, for example, five pre-installed 140mm fans. So there is no shortage of proper air circulation, and the only question is the noise level.
Interior
The case can accommodate the most common motherboard formats from Mini-ITX, mATX, to ATX. The original case has been reduced in length. This has resulted in the graphics card length dropping from 410 mm to 350 mm in the Arx 500 variant. This already leads to the case being incompatible with some larger graphics cards, but there are still plenty of options to choose from. The width of the case has remained the same, so you have 179 mm available for a tower CPU cooler here as well.
All vertical openings for cables have rubber grommets for a more cohesive look. Their width is the same both under the ceiling and along the motherboard. They offer you 24 mm of space for cable threading. With this width, you can even thread thicker cables through without any difficulty. Due to the shorter length, the Arx 500 is somewhat deprived of holes for mounting a liquid cooler reservoir. Compared to the original nine, there are only three.
The tunnel ceiling is just as superbly equipped as the larger version of the case. There are two larger holes directly under the motherboard. These make it much easier to handle cables when plugging them in. You can then also fit two 2.5″ storage devices to the tunnel by simply sliding them on using the dedicated screws and washers from the accessories. In the other half of the tunnel, you have space for mounting one 120 mm fan. There is also an additional grommet for power supply to the graphics card.
Due to the reduced length of the case, the space between the tunnel and the front panel is slightly smaller. With the original fan mount extensions, you only have 45 mm of space. But if you rotate the extensions, you get additional 30 mm. That means you don’t have to worry about not having enough room to accommodate even a thicker liquid cooler radiator.
To remove warm air from the case, the two 140 mm fans mentioned above are mounted under the ceiling. I have to appreciate that even with the smaller version of the case, the bracket for the cables from the fans has been preserved.
The back of the tray offers you five Velcro pull-tabs for cable management. That’s one less than you’ll get with the Arx 700. But you still have the single-use zip ties from the accessories. You can use these in the more than 20 other cable management positions. You have 22 mm of space directly behind the motherboard for cable management. Near the vertical grommets, the tray bends inwards towards the inside of the case, creating up to 35 mm of space for cabling there.
The metal plates of the Arx 500 are slightly thinner than those of the Arx 700. Their thickness is 0.65 mm, but this does not affect their stiffness at all, as their length is smaller. As a result, they are still just as stiff and do not bend.
You can mount two 2.5″ storage units on the tray in the same way as on the tunnel. You simply slide the storage drives into the holes using the screws and washers from the accessories. You have the option to mount another two directly to the rear frame of the case. Here you secure them with two screws. They don’t clash with anything here and at the same time the empty space of the case is used efficiently.
There is also a hub on the tray for the five mounted fans. The only drawback is that it only has five connectors. You can install up to seven fans in the case, so you’ll have to plug up to three connectors into the motherboard instead of one. That is, only if you want to increase the number of fans to the maximum.
The last option where to install storage is in the tunnel on the floor. Since it slides directly onto the floor, there’s no interference with the cables from the power supply. The good news is that this is a hybrid position. This gives you the option to also fit one 3.5″ drive in the case. But if you’ve already retired that format, you can still fit a 2.5″ storage drive in there as well.
For an ATX-format power supply, including its cables, you have a space of just over 310 mm.
Mounting the hardware is relatively quick. This is helped by the ample space inside the case on either side of the tray. This also made plugging in the cable to power the CPU convenient, even with the ceiling fan mounted. The latter, however, is easy to remove in case of difficulties. For cable management, there’s plenty of room for thicker cable bundles. Also thanks to the diverted grommets, plugging in and storing cables was easy.























