BeQuiet! Dark Base Pro 901: Nearly flawless full-tower

The new flagship BeQuiet! case is on sale now. The improvements over its predecessor are obvious, but there was a lot to draw from for the new Dark Base Pro 901. The ability to rotate the motherboard remained, and we can already reveal that it has a positive effect on cooling. This also makes this case suitable for the most powerful builds, which are associated not only with a lot of waste heat, but also with large dimensions of components.

Interior

Thanks to the generous space inside the case, you can fit even the largest hardware without restriction. Motherboards can fit inside in Mini-ITX, mATX, ATX and, after a small conversion, E-ATX formats up to 370 mm. Next to the motherboard standoffs are embossed letters, which you can assign to a specific motherboard format according to the legend on the tray. When choosing a graphics card, you don’t have to consider its length, as you have up to 495 mm of space for it in the Dark Base Pro 901. With a tower CPU cooler, it’s just as easy. You choose the one you want because there’s up to 190 mm of space for it in the case.

Above the tray there is an opening that is as tall as 50 mm, so you can thread every single cable through it without any hassle. Similarly, the hole below the tray is 15mm tall, ensuring easy plugging in even at the bottom of the motherboard.

   

Just behind the fans in the front, there are five plastic caps that cover the openings for alternative storage drawer locations. If the two that are in the case are not enough for you, it is possible to buy the „HDD Cage 2“ separately for around 14 EUR. If you mount positions that are parallel to the graphics card, the space for the graphics card is reduced to 380 mm.

But if you don’t need a large number of storage positions, you have the option to swap the frame behind the front fans. In the accessories you have a bracket for three 120 mm fans or a 120/240/360 mm format liquid cooler radiator. If you are fitting an E-ATX format motherboard, you must remove the original cabling cover (left photo) and replace it with the accessory replacement (right photo). This is due to the fact that the E-ATX motherboard format extends beyond the cabling holes on the tray and so it is necessary to use those directly on the replacement panel. This change is also possible on a panel with alternate positions for storage.

   

You will find one full plastic cover on the tunnel, which enhances its appearance even though its shade is different from the rest of the surrounding sheet metal. You can replace it with a perforated panel from the accessories. This directs the airflow using curved finning if you have a fan placed in the tunnel. The blowing is directed under the graphics card. With the covers, one or the other, you have up to 70 mm of space for a liquid cooler radiator and without it up to 200 mm. You can use that space for example to place a reservoir of your own custom loop.

   

The grille with caps for PCI Express expansion cards can be easily rotated 90 degrees with five screws. This allows you to mount the graphics card in a vertical position, facing the fans directly onto the glass side panel. However, this modification requires the separate purchase of a PCI Express slot extension cable with a support bracket.

   

The side of the tunnel consists of a plastic panel with the “Dark Base Pro” case series lettering, which can be removed. In addition to covering up the clutter under the tunnel in the form of cables, it has a thin strip of LEDs along its length. Along with the front panel and the top functional part of the case, these are the only backlit spots.

   

The most striking part of the back is certainly the cable management potential, as the case offers up to 30 mm of space behind the side panel. For efficient and easy cable management, up to four separate L-shaped sheets are provided, with holes on the inside prepared directly for Velcro strips. There are up to seven of these in the accessories, which are also long enough for larger cable bundles. I have to praise the separately allocated one grip only for the case cables, the number of which is higher. Of these, four flat cables of USB Type-A connectors of the same standard and also two cables with SATA connectors are worth mentioning. One for powering the function panel and the other for wireless charging.

Between the “L” panels are two holders for 2.5″ storage on the tray. They are attached quite simply, one side is hooked on the tray and the other is secured with a screw. This makes handling them very quick and convenient.

   

From the accessories, you have the option to use a cover for the cables of the storage devices that are installed on the panel with their alternative positions.

   

At the bottom of the tunnel are two drawers for 2.5″ and 3.5″ storage, which are installed on the additional frame with a single screw. The 3.5″ storage compartments are mounted via a hinged mechanism. Both the right and left sides have two levers that make it easy to secure the inserted storage without the need for screwing. You can fit up to two 2.5″ storage units in one compartment. One screws onto the bottom and the other onto the top.

   

The entire compartment can be removed and then a single 120/140 mm fan or even 5.25″ hardware can be fitted. The compartment can also be used for bottom mounting of a reservoir.

Behind the storage compartment, you have 330 mm of space for an ATX-format power supply with cabling. The latter is mounted from the back of the case through an additional mounting bracket, not through the side. The soft foam lining keeps it away from the perforated floor of the case. This means there is less chance of dirt being sucked in through the power supply.

One would think that there could be no difficulty in installing components into a case costing more than 300 euros. In our test setup, there was one, and that was with the stiffer cable for the motherboard power supply. The metal cover of the hole failed and the 24-pin cable pressed it out to such an extent that it had to be adjusted and slightly bent under its strain. Since it is removable, screwing it onto the tray also gave quite a bit of work. We have already encountered a similar problem with the Pure Base 500DX

A welcome addition when plugging in longer and also heavy graphics cards is the magnetic holder for them, which can be found in the accessories. The width of the holder also covers the multi-core power cables of the graphics cards. Through a small tunnel at the bottom, you can direct the power cable exactly as you need it.

   

The hardware installation itself was very easy, mainly due to the large space in the case and also the multiple removable parts. There was only one difficulty when plugging in the cabling with the relatively narrow vertical hole cover. Apart from that, the cable management was uncomplicated. I have to commend the huge space under the ceiling, which also made the connection of the cable for CPU power supply one of the easiest we’ve tested so far.

Managing the cabling from the back of the tray went swimmingly. Thanks to the 30 mm of space and the brackets, the cabling can be attached wherever it needs to be, making the overall installation much easier and less time-consuming. And as a bonus, the case will also forgive you for poorer cable management.

   

What also makes the case versatile is the ability to remove the tray via four screws, making it more convenient to mount the motherboard with the components already pre-prepared. Also, the entire design of the case is adapted to changing the sides of the tray. Thanks to this, you can have all the hardware situated on the right side instead of the left, which is the standard today. Of course, you have to count on extra work, it will take you 15-30 minutes depending on your skill.

The first thing to do is to disassemble the entire case, so to speak.

   

Then the cabling from the function panel, which is under the wireless charging cover, needs to be relocated to the other side of the case.

   

When the tray is inverted, not only the side of the tray changes but also the orientation by 180 degrees. So if you have a heavier graphics card and want to secure it, you need to mount a grip from the accessory.

   

Installing the hardware with the rotated tray, apart from the difficulty with the cover and the stiffer power cable for the motherboard, fortunately did not bring any new complications. I have a small observation from this rotated tray installation. Before securing the tray, with the motherboard and tower CPU cooler fitted, it is ideal to first plug in the cable for the CPU power supply. This is due to the subsequent lack of space between the hardware and the tunnel ceiling.

After flipping the tray, arranging the cabling with the cables reversed was slightly messy. Of course this is just a matter of habit. BeQuiet! has made a detailed instructional video for the tray flip, which is also referenced in the paper manual for the case.

   

The case can be almost completely disassembled but its sturdiness is not affected at all. All plates, frames and brackets are made to the millimetre to ensure no play. Also, the thickness of the plates, which are 0.9 mm, helps the rigidity.


Dark Power 14 (ATX 3.1) PSU up for grabs in summer giveaway

We’d like to give one HWCooling reader a BeQuiet! Dark Power 14 power supply. We’ll do it through a very simple competition, so let’s get right to it. There aren’t that many highly efficient power supplies (with an 80 Plus Titanium certification) featuring a quiet fan. In this giveaway, however, you can win one if you correctly answer the question in this article. So let’s get started! 🙂 Read more “Dark Power 14 (ATX 3.1) PSU up for grabs in summer giveaway” »

BeQuiet! also showcased keyboards and mice. Headsets not coming

Besides what BeQuiet! is best known for—PC components that go inside a case—the company also offers other PC hardware. The kind that connects to a computer (including laptops, of course), such as keyboards and mice. We also learned that anything producing sound is not currently on the horizon. So if you’re looking for an audio headset, you’ll have to turn elsewhere. More on that in this short report from Computex 2026. Read more “BeQuiet! also showcased keyboards and mice. Headsets not coming” »

BeQuiet! news: Dark Rock 6 (Pro) and expect Silent Wings 5

At Computex 2026, we learned what BeQuiet! has in preparation. And there is really quite a lot—besides new coolers, there were also new cases on display, and we also have some details about new fans. And actually about old ones too, at least regarding product lines that will no longer be further developed. In the first of two articles, we will first focus exclusively on BeQuiet! PC components, including power supplies. Read more “BeQuiet! news: Dark Rock 6 (Pro) and expect Silent Wings 5” »

One comment Add comment

  1. Overall, the be quiet! Dark Base Pro 901 is an excellent full-tower case that is perfect for enthusiasts and gamers who are looking for a case with excellent build quality, noise suppression, airflow, and features.

Leave a Reply

Your email address will not be published. Required fields are marked *