Alphacool SL-15 PWM: Low profile does not equal low airflow

The basis of the methodology, the wind tunnel

To write that we have something mapped out to the last detail is perhaps too bold, but after proper preparation, few pieces of hardware are as easy to evaluate as fans. Of course, this had to be preceded by long preparations, developing a methodology, but you already know the story. What you don’t know yet is the first fruit, or rather the results of Akasa, SilentiumPC, SilverStone, Xigmatek or more exotic Reeven fans.

The basis of the methodology, the wind tunnel

Before you start reading the methodology with all the details, take a look at the test tunnel as a whole. This is the heart of the whole system, to which other arteries are connected (manometer, vibrometer, powermeter, …). The only solid part of the tunnel from the measuring instruments is the anemometer.

The shape of the wind tunnel is inspired by the Venturi tube, which has long been used to measure the flow of liquids and gasses. The Venturi effect for wind speed measuring is also known from the aerospace industry. However, the design for measuring computer fans has its own specificities, which this proposal of ours reflects.

The individual parameters of the HWC wind tunnel for fan tests are the result of physical simulations and practical debugging. All the details (folds, material or finish used) have a rationale behind them and are designed this way for a specific reason. We will discuss the individual design details in turn in the description of the sub-variable measurements.

Now we will briefly elaborate on some things that do not fit thematically into the text of the following chapters. Namely, for example, that the skeleton of the wind tunnel is the work of a 3D printer (PLA). The rough print was, of course, then thoroughly machined by grinding, fusing, polishing and varnishing. Especially important is the smooth finish of the interior walls.

When joining the individual parts, the emphasis was on making sure that they fit together flawlessly, that they were sealed flawlessly (we will come back to this when we describe the test procedures for pressure measurement), but also that the joints were not loosened by use. Everything is disassemblable for servicing purposes, but it is ensured that the properties are maintained during use and, for example, even under the stress of vibration. The threads are secured with either lock nuts or thread-locking fluid. It depends on which is more suitable in which place.

When the wind tunnel is not in use, it is enclosed in a dust-tight chamber. In addition to the technical equipment and its correct storage, it is also important for objective outputs that all measuring instruments are calibrated according to the standard. Without this, it would be impossible to stand behind your results and rely on the manufacturers’ specifications. Calibration protocols are therefore an important part of the methodology. Testing is carried out at an ambient air temperature of 21–21.3 °C, humidity is approximately 45 % (± 2 %).

Fans come to us for testing in at least two pieces of the same model. If the deviations of any of the measured values are greater than 5 %, we also work with a third or fourth sample and the average value is formed by the results of the fans that came out the most similar and the differences between them fit under 5 %.


  •  
  •  
  •  
Flattr this!

The armored Apex Stealth fans promise the “impossible”

Alphacool has unleashed the new Apex Stealth fans on the world, which attract attention for two things in particular. Firstly, the fact that they contain robust metal elements and secondly, the specifications. These seem to be literally incredible, and while we have no doubt that the efficiency of these fans will be top notch, it’s hard to find elements for which they should be “the best”, as the specs suggest. Read more “The armored Apex Stealth fans promise the “impossible”” »

  •  
  •  
  •  

Alphacool introduces the “Core” series of high-speed fans

Six new models, with the slowest capping at 2,000 rpm and the fastest up to 4,000 rpm. It’s a mix of 120 and 140-millimeter fans, where with the larger format Alphacool reached for differently modeled rotors. This is also with a view to ensuring that a fan this fast and relatively large can operate at all at reasonably low vibration. Among Alphacool’s new products is therefore a fan with more robust blades as well. Read more “Alphacool introduces the “Core” series of high-speed fans” »

  •  
  •  
  •  

Plastic vs. metal backplate Alphacool (under LGA 1700)

For rather incomprehensible reasons, the cooling performance of the vast majority of AIO liquid coolers is degraded by the use of an unsuitable backplate. The backplate is usually undersized, made of plastic, and cannot exert optimal pressure on the processor. To give you an idea of how a “traditional” plastic backplate stacks up against a proper, steel one, we’ve prepared a comparison of the two. Read more “Plastic vs. metal backplate Alphacool (under LGA 1700)” »

  •  
  •  
  •  

Leave a Reply

Your email address will not be published. Required fields are marked *