Alphacool SL-15 PWM: Low profile does not equal low airflow

Everything changes with obstacles

To write that we have something mapped out to the last detail is perhaps too bold, but after proper preparation, few pieces of hardware are as easy to evaluate as fans. Of course, this had to be preceded by long preparations, developing a methodology, but you already know the story. What you don’t know yet is the first fruit, or rather the results of Akasa, SilentiumPC, SilverStone, Xigmatek or more exotic Reeven fans.

Everything changes with obstacles

So far, we have described how static pressure and airflow measurements are made under conditions where the fan has no obstacles in its path. In practice, however, fans do not usually blow into an empty space, but have a filter, grille or radiator in front of or behind them, the fins of which need to be pushed through as efficiently as possible.

A set of practical obstacles with which we measure the effect on airflow, static pressure, but also noise

We will also measure both airflow and pressure through practical obstacles for the reasons stated above. These include two types of filters that are usually used in PC cases. One fine – nylon and the other plastic with a thinner mesh. One other obstacle is the hexagonal grille perforated at 50%, on which the vast majority of fans – intake and exhaust – are installed. In some cases, we measure the effect of the obstacles on the results at positions (behind or in front of the rotor) that are used in practice. All obstacles are both pushed through to detect pressure drops, but also pulled through, which in turn speaks to the impact on airflow.

We use two radiators that differ in thickness and fin density. The EK CoolStream SE120/140 is 28 mm thick and the FPI is 22, the Alphacool NexXxoS XT45 v2 is thicker (45 mm) but with less FPI. CoolStream’s fin disposition is also similar in parameters to AIOs. The results on the NexXxoS will again be attractive for those who build their own water cooling loops, where the fans should work well even at low speeds – hence the lower fin density.
These obstacles and especially the radiators, but also the grilles, increase the mechanical resistance in front of the fan, resulting in higher noise levels. However, we will still tune the fan speeds to the specified noise levels of 31.5 to 45 dBA. Naturally, the speeds will always be lower than when testing without obstructions, but we will maintain the noise levels for clarity. The different noise levels with and without obstacles will only be at maximum power. In this mode it will also be nice to see how the fan design works with the obstacle and in which case the noise level increases more and in which less.


  •  
  •  
  •  
Flattr this!

The armored Apex Stealth fans promise the “impossible”

Alphacool has unleashed the new Apex Stealth fans on the world, which attract attention for two things in particular. Firstly, the fact that they contain robust metal elements and secondly, the specifications. These seem to be literally incredible, and while we have no doubt that the efficiency of these fans will be top notch, it’s hard to find elements for which they should be “the best”, as the specs suggest. Read more “The armored Apex Stealth fans promise the “impossible”” »

  •  
  •  
  •  

Alphacool introduces the “Core” series of high-speed fans

Six new models, with the slowest capping at 2,000 rpm and the fastest up to 4,000 rpm. It’s a mix of 120 and 140-millimeter fans, where with the larger format Alphacool reached for differently modeled rotors. This is also with a view to ensuring that a fan this fast and relatively large can operate at all at reasonably low vibration. Among Alphacool’s new products is therefore a fan with more robust blades as well. Read more “Alphacool introduces the “Core” series of high-speed fans” »

  •  
  •  
  •  

Plastic vs. metal backplate Alphacool (under LGA 1700)

For rather incomprehensible reasons, the cooling performance of the vast majority of AIO liquid coolers is degraded by the use of an unsuitable backplate. The backplate is usually undersized, made of plastic, and cannot exert optimal pressure on the processor. To give you an idea of how a “traditional” plastic backplate stacks up against a proper, steel one, we’ve prepared a comparison of the two. Read more “Plastic vs. metal backplate Alphacool (under LGA 1700)” »

  •  
  •  
  •  

Leave a Reply

Your email address will not be published. Required fields are marked *