You already know the impressive features of the new aerodynamic design of Arctic’s 7-blade fans from our earlier tests. Now we add the results for the ARGB LED versions (P12 Pro A-RGB), which are naturally quite similar, but also show certain differences due to a more light-conductive material. That’s why it’s worth taking another look. The title of this review already hints at where things are heading.
33 dBA or 33 dBA
The noise level, given as a single dBA value, is good for quick reference, but it doesn’t give you an idea of exactly what the sound sounds like. That’s because it averages a mix of noise levels of all frequencies of sound. One fan may disturb you more than the other, even though they both reach exactly the same dBA, yet each is characterized by different dominant (louder) frequencies. To analyze thoroughly with an idea of the “color” of the sound, it is essential to record and assess noise levels across the entire spectrum of frequencies that we perceive.

We already do this in graphics card tests, and we’ll do it for fans too, where it makes even more sense. Using the UMIK-1 miniDSP microphone and TrueRTA’s mode-specific, fixed dBA application, we also measure which frequencies contribute more and which contribute less to the sound. The monitored frequency range is 20-20,000 Hz, which we’ll work with at a fine resolution of 1/24 octave. In it, noise levels from 20 Hz to 20 000 Hz are captured at up to 240 frequencies.
The information captured in the spectrograph is a bit more than we will need for clear fan comparisons. While you’ll always find a complete spectrograph in the tests, we’ll only work with the dominant frequencies (and their noise intensities) in the low, mid, and high bands in the comparison tables and charts. The low frequency band is represented by 20–200 Hz, the medium by 201–2000 Hz and the high by 2001–20 000 Hz. From each of these three bands, we select the dominant frequency, i.e. the loudest one, which contributes most to the composition of the sound.
To the dominant frequency we also give the intensity of its noise. However, in this case it is in a different decibel scale than those you are used to from noise meter measurements. Instead of dBA, we have dBu. This is a finer scale, which is additionally expressed negatively. Be careful of this when studying the results – a noise intensity of -70 dBu is higher than -75 dBu. We discussed this in more detail in the article Get familiar with measuring the frequency response of sound.
Strict acoustic safeguards are required to ensure that these measurements can be carried out with satisfactory repeatability at all. We use acoustic panels to measure the same values at all frequencies across repeated measurements. These ensure that the sound is always reflected equally to the microphone regardless of the distribution of other objects we have in the testlab. The baseline noise level before each measurement is also naturally the same. The room in which we measure is soundproofed.

Like the noise meter, the microphone has a parabolic collar to increase resolution. The latter is specially in this case not only to amplify but also to filter out the noises that occur whether we want them or not behind the microphone. We are talking about the physical activity of the user (tester). Without this addition, human breathing, for example, would also be picked up by the spectrograph. However, this is successfully reflected off the microphone sensor by the back (convex) side of the collar. As a result, the spectrogram only contains information about the sound emitted by the fan itself.







Here we have some direct comparisons with the predecessor (filter, grille, radiator). I think the A‑RGB Pros are a good choice as system fans. For radiators, I don’t think so.
Many thanks! 🙂
Do you think it deserves a Top Notch award?
While the static pressure is over the roof, the actual airflow compared to the other new RGB fan is comparable at best. On one hand, the airflow w/o obstacle and on hexagonal grid lags significantly behind the Momentum RGB, on the other hand, it beats it on plastic filter (due to high static pressure). The P12 Pro is slightly better with radiators, but not far from the Momentum RGB. However, the potential collision with the nylon dust filter prevents it from achieving such a rare award on this site.
At least, that my view, why Ľubo gives it the “Smurt buy” award, where it clearly dominates…although he certainly considered also the “top-notch” award, but…. 😉
–“… “Smurt buy” award, where it clearly dominates…
I overdid it… 😀
…but I was thinking among RGB fans …and taking static pressure into account 😉
I did consider giving it the “Top-notch” award, but in my opinion, the Arctic P12 Pro A-RGB has shortcomings in other areas that hold it back. Sure, it’s excellent in terms of aerodynamics, but it’s still a fan with clear signs of manufacturing compromises. I believe awarding it a more prestigious title like “Top-notch” would be unfair — for example, to a fan like the FD Momentum 12 RGB.