Fractal Design Venturi HP-14 PWM: Against vibrations above all

Cooling, Extra tests, Fans | | Ľubomír Samák

Overview of manufacturer specifications

Venturi fans have some of the softest mounting corners. The transmission of vibrations from moving parts further away to anything (case plates, heatsink fins, …) is thus very significantly damped. Compared to other (even more modern Fractal Design models), these fans have more robust blades, which are both thicker and wider, and as a result, higher static pressure is also achieved at comparable speeds.

* When reading performance values, a certain amount of tolerance must always be taken into account. For maximum speeds, ±10 % is usually quoted, minimum speeds can vary considerably more from piece to piece, sometimes manufacturers will overlap by as much as ±50 %. This must then also be adequately taken into account for air flow, static pressure and noise levels. If only one value is given in a table entry, this means that it always refers to the situation at maximum speed, which is achieved at 12 V or 100 % PWM duty cycle. The manufacturer does not disclose the lower limit of the performance specifications in its materials in that case. The price in the last column is always approximate.
** Price calculated per unit, but the fan is not sold separately. It is only available as part of a three-pack that also includes an ARGB hub.


  •  
  •  
  •  
Continue:
Flattr this!

Related articles

Noctua NF-A14x25 G2 PWM: Finally a first-class 140mm fan

Cooling, Extra tests, Fans | | Ľubomír Samák

The range of 140mm fans is now expanded by the Noctua NF-A14x25 G2 PWM. The wait for this model was very long, but finally, after various hardships, everything was brought to a successful end. This, by the way, is also indicated by our in-depth tests, from which the NF-A14x25 G2 fan takes away the “best” results across many usage scenarios. This is also due to the significant innovations in the aerodynamic design. Read more “Noctua NF-A14x25 G2 PWM: Finally a first-class 140mm fan” »

  •  
  •  
  •  

We wrote 7 years ago. Tests you may have overlooked

Cooling, Extra tests, News | | Ľubomír Samák

Some articles become obsolete faster, others are relevant for a long time. Such, more durable ones usually do not focus on a specific product, but on a topic as a whole, with a pinch of generality. Articles like this have always been given space around here, since the beginning of HWCooling, and it probably doesn’t hurt to bring them up again. Well, at least as part of this selection which would be a shame to miss forever. Read more “We wrote 7 years ago. Tests you may have overlooked” »

  •  
  •  
  •  

Noctua on measuring fan noise: Different angles, different results

Cooling, Fans, Interview | | Ľubomír Samák

Noise measurements are an extremely complex topic. Imagine you have ten different sound sources. The noise from each will radiate through the space in different ways, and measuring ‘which is the noisiest’ and coming up with a clear verdict on that is a really hard nut to crack. To give you a better idea, we’ve interviewed Noctua. Different measurement techniques yield potentially different and sometimes contradictory conclusions. Read more “Noctua on measuring fan noise: Different angles, different results” »

  •  
  •  
  •  

Comments (2) Add comment

  1. I wonder the reason why these type of corners, despite being so effective, are uncommon. Is it a lack of necessity due to inherent low vibrations, rubber pads/mounts being good enough/better, or some kind of cost or mechanical concerns?

    Reply

    1. It’s hard to say anything for sure. But I will dare to speculate.

      Let’s assume that higher vibrations characterize mainly the cheaper fans, where the goal was to make them as cheap as possible. All-rubber corners don’t fit into this scheme (lowest cost) (such Arctic P12 don’t even have rubber pads), so they are usually not used. And again, when there is a bigger budget for fans, the funds can be put into things that suppress vibrations more effectively than perfect anti-vibration corners. Whether it’s a stiffer material (just with a larger thickness or a different composition, for example LCP instead of PBT) or a less vibrating motor etc.

      Reply

Leave a Reply

Your email address will not be published. Required fields are marked *