SilentiumPC Fluctus 120 PWM: “Miracle” fan from the Fera 5

Base 7 equal noise levels…

To write that we have something mapped out to the last detail is perhaps too bold, but after proper preparation, few pieces of hardware are as easy to evaluate as fans. Of course, this had to be preceded by long preparations, developing a methodology, but you already know the story. What you don’t know yet is the first fruit, or rather the results of Akasa, SilentiumPC, SilverStone, Xigmatek or more exotic Reeven fans.

Base 7 equal noise levels

There are several options by which to normalize the test modes for fans. In the previous chapter, we wrote that perhaps the least appropriate option is equal speed.
Settings according to the same static pressure or flow are for consideration, but we find it most sensible in the long term to normalize the measurement modes according to the same noise levels. Firstly because decibels are a logarithmic unit and all others scale linearly, but mainly because you can orientate fastest by the same noise levels. The easiest way to compare the efficiency of fans is just by how they perform at the same sound pressure level. Of all the options, this is the one that most people can best imagine and bounce off of when considering other variables.

The individual noise level modes are adjusted from low levels continuously to higher levels. All users will find their results in the tests, regardless of whether they prefer very quiet operation at the limit of audibility or whether high performance is paramount.
The quietest mode corresponds to 31.5 dBA, followed by 33 dBA, and for each additional mode we add 3 dBA, which always doubles the noise level (36, 39, 42 and 45 dBA). Finally, we measure the fans at maximum power. Here, each one already has a slightly different noise level, which we also report. If there are missing measurements between the results for any of the fans, this means that it was not possible to set the target noise level. Either because its minimum speed exceeds the quietest mode of 31.5 dBA or vice versa because the fan is quieter than 45 dBA at maximum power.
It is important to add that our noise level measurements are incomparable to the values quoted by the fan manufacturers in their specifications. One of the reasons is because we use a parabola-shaped collar around the sensor of the noise meter, which increases sensitivity. This is important in order to distinguish and set to the same noise level even modes at very low speeds, especially 31.5 dBA.
The noise meter next to the fan is quite close for sufficient resolution. The distance between the frame and the sensor is 15 centimeters. The sensor is positioned in such a way that there is no distortion or that the noise level measurements are not affected by airflow. Therefore, the noise meter is centered perpendicularly to the frame that defines the depth of the fan. Everything is always at the same angle and at the same distance. We use an inclinometer and markers to set the distances precisely and always the same.

The noise meter sensor is positioned relative to the position of the fan from the profile. It is centered to the depth of the frame both vertically and horizontally.

We use a Reed R8080 noise meter to measure noise levels. This allows real-time averaging of samples, which is important for fine-tuning individual modes. We tune the fans until the specified noise level is reached to two decimal places, for example 31.50 dBA. The noise meter is the only instrument we calibrate inside our testlab. The other instruments have been calibrated by the relevant technical institutes. However, in the case of the noise meter, calibration is required before each test and we therefore have our own calibrator. This is already calibrated externally according to the standard.


  •  
  •  
  •  
Flattr this!

New Arctic P14 Max: Anti-vibration and high speed

Those interested in 140mm fans have reason to rejoice. After the P12 Max, Arctic is also releasing the P14 Max, which is one size larger. These stick to the already established features, such as a significant speed increase, but also probably a noise reduction even at low speeds. By all accounts, these should be universal fans that will be efficient across the entire speed spectrum, and on all types of obstacles. Read more “New Arctic P14 Max: Anti-vibration and high speed” »

  •  
  •  
  •  

Release of Noctua’s 140mm next-gen fans sticks to schedule

The title couldn’t fit a “despite complications with the frame”. Even though Noctua figured out that the fan blades could collide under adverse circumstances due to deformation of the frame in a more advanced stage of prototyping, it seems that the fix for this inconvenience didn’t take too long. We’re again at the point where it looks like Noctua’s 140mm LCP fans are right outside the doors of the retail market. Read more “Release of Noctua’s 140mm next-gen fans sticks to schedule” »

  •  
  •  
  •  

Thermaltake Toughfan 14 Pro: Number one for radiators

While the selection of high-end 140mm fans is quite narrow, there is one model that may be of interest to you. Especially if you want the “most effective” for your radiator, at low noise levels. Certain features of the high-end admittedly don’t appear on the Toughfan 14 Pro, but when it comes to cooling radiators, Thermaltake’s fan doesn’t have much competition in this discipline. It will defend its place in silent builds. Although… Read more “Thermaltake Toughfan 14 Pro: Number one for radiators” »

  •  
  •  
  •  

Leave a Reply

Your email address will not be published. Required fields are marked *